Follow us on Have any questions? Just call us 952-935-2345

News & Events

A Simple Guide to Coil Circuiting


A Simple Guide to Coil Circuiting

Circuiting of fluid coils is important to the performance and life of the coil, yet for even seasoned professionals it can be confusing. However, it really isn't as difficult as it seems. 

What is circuiting?

In the simplest terms, circuiting means the number of tubes on any coil being fed by each header. Every coil has a specific number of rows, and a specific number of tubes within each row. For example, in the illustration below we show a coil that is 8 tubes high and 4 rows deep for a total of 32 tubes (in another case, you could have a coil that is 24 tubes high and 8 rows deep for a total of 192 tubes). In this initial example, the "supply" enters from the right and the "return" exits on the left. (Note: Most fluid coils have the supply and return connections on the same end of the coil.)

Hot or cold fluid enters through the supply connection, fills up the manifold, and then simultaneously feeds the tubes in each circuit. The number of tubes that are fed by each header (or number of circuits) ultimately depends on the performance you need from that coil. Circuiting is really a balancing act of tube velocity and pressure drop.  

Determining the right number of circuits

To ensure proper heat transfer, fluid must travel through coils at the right speed. Some coils only have a small number of circuits while others have quite a few. If fluid travels too quickly through the coil, the heat transfer will be inefficient, the coil could have a high pressure drop, and this situation could cause tube erosion. If it travels too slowly, only a little heat transfer will occur. By selecting the appropriate number of circuits, you control the fluid speed and thus the heat transfer efficiency of the coil.

Fewer circuits serves to speed up the fluid in the coil, while more circuits slow it down. For example, feeding a larger number of tubes simultaneously spreads the flow of fluid to multiple circuits, which slows down the speed at which it flows through the coil. The number of circuits and the inside diameter of the tubes allows you to calculate total flow rate (in GPM) of the coil.

If a coil has 8 tubes per row and is 4 rows deep, as shown in our example, then the circuiting is as follows:

  • Half Circuit – 4 feeds 
  • Quarter Circuit – 2 feeds
  • Full Circuit – 8 feeds 
  • Double Circuit – 16 feeds 

Finally, here are 3 rules of thumb to follow regarding coil circuiting:

  1. The number of tubes you feed must divide evenly into the number of tubes in the coil or you will have dropped tubes (tubes that aren't fed fluid).  
  2. The coil must have an even number of passes if you want connections to end up on the same end of the coil. With an odd number of passes, you will have fluid connections on opposite ends.
  3. The number of  circuits will determine the resulting pressure drop by determining the number of circuits and thus the fluid velocity and effective tube length for each circuit (acceptable fluid tube velocity is between 2 and 7 feet per second). 

Contact Campbell-Sevey

If you want to ensure that the most efficient number of circuits are being used for your replacement coils, simply contact the team at Campbell-Sevey. 

 

No comments (Add your own)

Add a New Comment


code
 

Comment Guidelines: No HTML is allowed. Off-topic or inappropriate comments will be edited or deleted. Thanks.

Subscribe to our CS Update Newsletter: Send Me The Latest News

952-935-2345  emailmain@campbell-sevey.com  address15350 Minnetonka Blvd., Minnetonka, MN 55345

Products We Carry

GENERATION
  • Hot Water Boilers
  • Watertube Steam Boilers
  • Firetube Steam Boilers
  • Deaerators
  • Heat Recovery Steam Generators (HRSG’s)
  • Automatic Recirculation Valves
  • Economizers
  • Gas-Fired Water Heaters
  • Gas-Fired Humidifiers
  • Boiler/Generator Flue Stacks
  • Continuous Emissions Monitors (CEMS)
DISTRIBUTION
  • Pressure Reducing Valves
  • Safety and Relief Valves
  • Control Valves
  • Pressure Independent Control Valves
  • Expansion Joints, Guides, Anchors
  • Flash Tanks
  • Flow Meters
  • Balancing Valves
  • Check Valves
  • Separators
  • Pumps
  • Pressure Booster Systems
  • Piston Valves
UTILIZATION
  • Heating/Cooling Coils
  • Plate and Frame Heat Exchangers
  • Shell and Tube Exchangers
  • Water Heaters
  • Steam Humidifiers
  • Vacuum Systems
  • Condensers
  • Steam Traps
  • Wireless Steam Trap Monitors
  • Tube Bundles
  • Direct Gas-Fired Space Heaters
  • Direct Gas-Fired Make-Up Air Units
  • Unit Heaters
  • Strainers
  • Air Vents
  • Liquid Drainers
  • Heat Transfer Packages
  • Digital Water Mixing Valves
  • Air Cooled Condensers/Dry Coolers
  • Steam Filters
RETURN
  • Electric Condensate Pumps
  • Steam/Air-Powered Condensate Pumps
  • Packaged Condensate Pump Skids